- Englisch (5) (entfernen)
- Customer loads correlation in truck engineering (2009)
- Safety and reliability requirements on the one side and short development cycles, low costs and lightweight design on the other side are two competing aspects of truck engineering. For safety critical components essentially no failures can be tolerated within the target mileage of a truck. For other components the goals are to stay below certain predefined failure rates. Reducing weight or cost of structures often also reduces strength and reliability. The requirements on the strength, however, strongly depend on the loads in actual customer usage. Without sufficient knowledge of these loads one needs large safety factors, limiting possible weight or cost reduction potentials. There are a lot of different quantities influencing the loads acting on the vehicle in actual usage. These ‘influencing quantities’ are, for example, the road quality, the driver, traffic conditions, the mission (long haulage, distribution or construction site), and the geographic region. Thus there is a need for statistical methods to model the load distribution with all its variability, which in turn can be used for the derivation of testing specifications.
- Calculating invariant loads for system simulation in vehicle engineering (2009)
- For the numerical simulation of a mechanical multibody system (MBS), dynamical loads are needed as input data, such as a road profile. With given input quantities, the equations of motion of the system can be integrated. Output quantities for further investigations are calculated from the integration results. In this paper, we consider the corresponding inverse problem: We assume, that a dynamical system and some reference output signals are given. The general task is to derive an input signal, such that the system simulation produces the desired reference output. We present the state-of-the-art method in industrial applications, the iterative learning control method (ILC) and give an application example from automotive industry. Then, we discuss three alternative methods based on optimal control theory for differential algebraic equations (DAEs) and give an overview of their general scheme.
- Undesired drift of multibody models excited by measured accelerations or forces (2009)
- In the ground vehicle industry it is often an important task to simulate full vehicle models based on the wheel forces and moments, which have been measured during driving over certain roads with a prototype vehicle. The models are described by a system of differential algebraic equations (DAE) or ordinary differential equations (ODE). The goal of the simulation is to derive section forces at certain components for a durability assessment. In contrast to handling simulations, which are performed including more or less complex tyre models, a driver model, and a digital road profile, the models we use here usually do not contain the tyres or a driver model. Instead, the measured wheel forces are used for excitation of the unconstrained model. This can be difficult due to noise in the input data, which leads to an undesired drift of the vehicle model in the simulation.
- Comparison of the solutions of the elastic and elastoplastic boundary value problems (2006)
- In this article, we consider the quasistatic boundary value problems of linear elasticity and nonlinear elastoplasticity, with linear Hooke’s law in the elastic regime for both problems and with the linear kinematic hardening law for the plastic regime in the latter problem. We derive expressions and estimates for the difference of the solutions of both models, i.e. for the stresses, the strains and the displacements. To this end, we use the stop and play operators of nonlinear functional analysis. Further, we give an explicit example of a homotopy between the solutions of both problems.
- MSB Simulation of a hexapod based suspension test rig (2006)
- Testing a new suspension based on real load data is performed on elaborate multi channel test rigs. Usually wheel forces and moments measured during driving maneuvers are reproduced on the rig. Because of the complicated interaction between rig and suspension each new rig configuration has to prove its efficiency with respect to the requirements and the configuration might be subject to optimization. This paper deals with modeling a new rig concept based on two hexapods. The real physical rig has been designed and meanwhile built by MOOG-FCS for VOLKSWAGEN. The aim of the simulation project reported here was twofold: First the simulation of the rig together with real VOLKSWAGEN suspension models at a time where the design was not yet finalized was used to verify and optimize the desired properties of the rig. Second the simulation environment was set up in a way that it can be used to prepare real tests on the rig. The model contains the geometric configuration as well as the hydraulics and the controller. It is implemented as an ADAMS/Car template and can be combined with different suspension models to get a complete assembly representing the entire test rig. Using this model, all steps required for a real test run such as controller adaptation, drive file iteration and simulation can be performed. Geometric or hydraulic parameters can be modified easily to improve the setup and adapt the system to the suspension and the load data.