Kaiserslautern - Fachbereich Physik
Refine
Year of publication
Document Type
- Article (94) (remove)
Language
- English (94)
Has Fulltext
- yes (94)
Keywords
- resonances (8)
- Wannier-Stark systems (7)
- lifetimes (7)
- Quantum mechanics (6)
- quantum mechanics (5)
- lifetime statistics (4)
- entropy (3)
- localization (3)
- dynamical systems (2)
- phase-space (2)
Faculty / Organisational entity
Using molecular dynamics simulation, we study the cutting of an Fe single crystal using
tools with various rake angles α. We focus on the (110)[001] cut system, since here, the crystal
plasticity is governed by a simple mechanism for not too strongly negative rake angles. In this
case, the evolution of the chip is driven by the generation of edge dislocations with the Burgers
vector b = 1
2
[111], such that a fixed shear angle of φ = 54.7◦
is established. It is independent of
the rake angle of the tool. The chip form is rectangular, and the chip thickness agrees with the
theoretical result calculated for this shear angle from the law of mass conservation. We find that the
force angle χ between the direction of the force and the cutting direction is independent of the rake
angle; however, it does not obey the predictions of macroscopic cutting theories, nor the correlations
observed in experiments of (polycrystalline) cutting of mild steel. Only for (strongly) negative rake
angles, the mechanism of plasticity changes, leading to a complex chip shape or even suppressing the
formation of a chip. In these cases, the force angle strongly increases while the friction angle tends
to zero.
Using molecular dynamics simulation, we study nanoindentation in large samples of Cu–Zr glass at various temperatures between zero and the glass transition temperature. We find that besides the elastic modulus, the yielding point also strongly (by around 50%) decreases with increasing temperature; this behavior is in qualitative agreement with predictions of the cooperative shear model. Shear-transformation zones (STZs) show up in increasing sizes at low temperatures, leading to shear-band activity. Cluster analysis of the STZs exhibits a power-law behavior in the statistics of STZ sizes. We find strong plastic activity also during the unloading phase; it shows up both in the deactivation of previous plastic zones and the appearance of new zones, leading to the observation of pop-outs. The statistics of STZs occurring during unloading show that they operate in a similar nature as the STZs found during loading. For both cases, loading and unloading, we find the statistics of STZs to be related to directed percolation. Material hardness shows a weak strain-rate dependence, confirming previously reported experimental findings; the number of pop-ins is reduced at slower indentation rate. Analysis of the dependence of our simulation results on the quench rate applied during preparation of the glass shows only a minor effect on the properties of STZs.
The first observation of self-focusing of dipolar spin waves in garnet film media is reported. In particular, we show that the quasi-stationary diffraction of a finite-aperture spin wave beam in a focusing medium leads to the concentration of the wave power in one focal point rather than along a certain line (channel). The obtained results demonstrate the wide applicability of non-linear spin wave media to study non-linear wave phenomena using an advanced combined microwave-Brillouin light scattering technique for a two-dimensional mapping of the spin wave amplitudes.
This contribution presents the results of a replication study on the learning effect of tablet-supported video analysis compared to traditional teaching sequences using non-digital experimental materials in the subject areas of uniform and accelerated motion in high school physics lessons. In addition to the replication of the preliminary study results recently published in this journal (Becker et al 2018, 2019), the investigation of the effect on the cognitive load as well as the emotional state of the students is another focal point. Compared to the preliminary study, the sample size was significantly increased from N = 109 to N = 294. The individual effects of the preliminary study could be replicated in this way. For both topics, a significant reduction of extraneous cognitive load and a positive effect on intervention-induced emotions could be demonstrated. Moreover, the theoretically founded causal relationship between emotion, cognitive load, and learning achievement could be empirically verified by means of structural equation modeling.
With the transition of fluid-capillary-based “Lab on a chip 1.0″ concepts in analytical chemistry to “Lab on a chip
2.0″ approaches relying on distinct fluid droplets (“digital microfluidics”, DMF), the need for reliable methods for
droplet actuation has increasingly come into focus. One possible approach is based on “electrowetting on
dielectric” (EWOD). This technique has the disadvantage that any possible desired later positions of the droplets
on the chip have to be defined prior to chip realization because one of the EWOD electrode layers has to be
structured accordingly. “Optoelectrowetting” (OEW) goes a step further in the sense that the later droplet positions
do not have to be known before, and none of the electrode layers has to be structured. Instead, the
electrical parameters of the layer sequence can be altered locally by an impinging (and movable) light spot.
Although some research groups have succeeded in demonstrating OEW actuation of droplets, the optimization of
the relevant parameters of the layer sequence and the droplet – at least half a dozen parameters altogether – is
tedious and not straight-forward. In this contribution, for optimization purposes, the equations governing OEW
are revisited and altered again, e.g., by numerical implementation of the experimentally well-known saturation
of the contact angle change. Additionally, a Nelder-Mead algorithm is applied to find the parameters, on which
the optimization has to focus to maximize contact angle changes and, thus, mechanical forces on the droplets.
The numerical investigation yields diverse results, e.g., the finding that the droplet’s contact area on the
dielectric layer has a strong influence on the contact angle change and the question whether the droplet is pulled
or pushed. Moreover, the interplay between frequency and amplitude of the applied rectangular alternate voltage
is important for optimization.
Low damping magnetic properties and perpendicular magnetic anisotropy in the Heusler alloy Fe1.5CoGe
(2019)
We present a study of the dynamic magnetic properties of TiN-buffered epitaxial thin films of the Heusler alloy Fe1.5CoGe. Thickness series annealed at different temperatures are prepared and the magnetic damping is measured, a lowest value of α = 2.18 × 10−3 is obtained. The perpendicular magnetic anisotropy properties in Fe1.5CoGe/MgO are also characterized. The evolution of the interfacial perpendicular anisotropy constant K⊥S with the annealing temperature is shown and compared with the widely used CoFeB/MgO interface. A large volume contribution to the perpendicular anisotropy of (4.3 ± 0.5) × 105 J/m3 is also found, in contrast with vanishing bulk contribution in common Co- and Fe-based Heusler alloys.
An unusual interlayer coupling, recently discovered in layered magnetic systems, is analysed from the experimental and theoretical points of view. This coupling favours the 90° orientation of the magnetization of the adjacent magnetic films. It can be phenomenologically described by a term in the energy expression, which is biquadratic with respect to the magnetizations of the two films. The main experimental findings, as well as the theoretical models, explaining the phenomenon are discussed.
Deactivation processes of photoexcited (λex = 580 nm) phycocyanobilin (PCB) in methanol were investigated by means of UV/Vis and mid-IR femtosecond (fs) transient absorption (TA) as well as static fluorescence spectroscopy, supported by density-functional-theory calculations of three relevant ground state conformers, PCBA, PCBB and PCBC, their relative electronic state energies and normal mode vibrational analysis. UV/Vis fs-TA reveals time constants of 2.0, 18 and 67 ps, describing decay of PCBB*, of PCBA* and thermal re-equilibration of PCBA, PCBB and PCBC, respectively, in line with the model by Dietzek et al. (Chem Phys Lett 515:163, 2011) and predecessors. Significant substantiation and extension of this model is achieved first via mid-IR fs-TA, i.e. identification of molecular structures and their dynamics, with time constants of 2.6, 21 and 40 ps, respectively. Second, transient IR continuum absorption (CA) is observed in the region above 1755 cm−1 (CA1) and between 1550 and 1450 cm−1 (CA2), indicative for the IR absorption of highly polarizable protons in hydrogen bonding networks (X–H…Y). This allows to characterize chromophore protonation/deprotonation processes, associated with the electronic and structural dynamics, on a molecular level. The PCB photocycle is suggested to be closed via a long living (> 1 ns), PCBC-like (i.e. deprotonated), fluorescent species.
A measurement technique, i.e. reflectance anisotropy/difference spectroscopy (RAS/RDS), which had originally been developed for in-situ
epitaxial growth control, is employed here for in-situ real-time etch-depth control during reactive ion etching (RIE) of cubic crystalline III/V
semiconductor samples. Temporal optical Fabry-Perot oscillations of the genuine RAS signal (or of the average reflectivity) during etching due
to the ever shrinking layer thicknesses are used to monitor the current etch depth. This way the achievable in-situ etch-depth resolution has
been around 15 nm. To improve etch-depth control even further, i.e. down to below 5 nm, we now use the optical equivalent of a mechanical
vernier scale– by employing Fabry-Perot oscillations at two different wavelengths or photon energies of the RAS measurement light – 5%
apart, which gives a vernier scale resolution of 5%. For the AlGaAs(Sb) material system a 5 nm resolution is an improvement by a factor of 3
and amounts to a precision in in-situ etch-depth control of around 8 lattice constants.
Meanwhile, electrowetting-on-dielectric (EWOD) is a well-known phenomenon, even often exploited in active micro-optics to
change the curvature of microdroplet lenses or in analytical chemistry with digital microfluidics (DMF, lab on a chip 2.0) to move/
actuate microdroplets. Optoelectrowetting (OEW) can bring more flexibility to DMF because in OEW, the operating point of the
lab chip is locally controlled by a beam of light, usually impinging onto the chip perpendicularly. As opposed to pure EWOD, for
OEW, none of the electrodes has to be structured, which makes the chip design and production technology simpler; the path of
any actuated droplet is determined by the movement of the light spot. However, for applications in analytical chemistry, it would
be helpful if the space both below as well as that above the lab chip were not obstructed by any optical components and light
sources. Here, we report on the possibility to actuate droplets by laser light beams, which traverse the setup parallel to the chip
surface and inside the OEW layer sequence. Since microdroplets are grabbed by this surface-parallel, nondiverging, and
nonexpanded light beam, we call this principle “light line OEW” (LL-OEW).