UNIVERSITÄTSBIBLIOTHEK
The search result changed since you submitted your search request. Documents might be displayed in a different sort order.
  • search hit 10 of 1
Back to Result List

Experimental Investigation of Mass Flow Rate and Pressure-drop through Rupture Disk Devices with Compressible Two-Phase Flow

  • The Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment (European Commision, 1997) is the basis of the legal framework for protection of pressure equipment within the European Union. Codes and standards are useful to comply with the legal and regulatory responsibilities stipulated in PED Directive regarding the protection of pressure equipment against overpressure, sizing, and selection safety relief devices. Rupture disk devices are primary relief devices to protect vessels, pipe, and equipment against overpressure. A rupture disk bursts once the so-called burst pressure is reached in the protected system, thereby discharging flow and preventing further increase in pressure. Currently, rupture disks are sized with standards and codes assuming the worst-case scenario at burst pressure. There is however no standardized procedure for sizing rupture disks with two-phase flow and there lacks suited test-facilities, test-sections, and reliable experimental data for model validation. Sizing rupture disk vent-line systems with current characteristic numbers comes with significant uncertainties, especially for high-velocity compressible flows (Schmidt, 2015). Zero-Emission and Green Safety are current trends for organizations that seek to attain innovative protection concepts beyond regulatory compliance. A procedure to size a rupture disk vent-line should accurately determine the discharge rate and pressure-drop across a rupture disk, from the point of rupture disk activation to the point when the system depressurizes fully. This procedure is critical for further safety considerations, such as for modeling the dispersion of toxic gases released during emergency-relief and calculating the emissions to the environment with time. Over-dimensioning is one measure taken today to mitigate uncertainties encountered while sizing with current methods. This is not always an option, as over-dimensioning the rupture disk vent-line system leads to unnecessary financial costs. It may also cause malfunction of the collecting systems downstream when the fluids discharged are more than the design limits. Emissions to the environment are thereby potentially higher than necessary, causing excessive harm to the environment. Under-dimensioning, on the other hand, may lead to hazardous incidents with loss of human life and equipment. This work has therefore focused on the investigation of the mass flow rate and pressure-drop through rupture disk devices with compressible gas and two-phase flow. The experimental focus was in the design, construction, and commissioning of a high-capacity, high-pressure industry-scale test facility for testing small- to large-diameter rupture disks and other fittings with gas flow. The resulting test facility is suited to test safety devices and pipe fittings at near realistic flow conditions at pressures up to 150 bar. This work also presents the design of a pilot plant for testing rupture disks with air/water two-phase flow. These test facilities open-up new frontiers for capacity testing because they have precise and state-of-the-art measurement and instrumentation. Experimental results from these facilities deliver reliable experimental data to validate proposed sizing procedures for rupture disk devices. The theoretical focus was on the development of a reliable rupture disk sizing procedure for compressible gas and two-phase flow. This required phenomenological studies of flow through rupture disks with both experiments and CFD studies. Better suited rupture disk characteristic numbers and model parameters for determining the mass flow rate and pressure-drop across rupture disks are identified. The proposed sizing procedure with compressible gas and two-phase flow predicts the dischargeable mass flow rate and pressure-drop across a rupture disk within ±4 % of measured value. Experimental validation has been undertaken with different types of rupture disks. The procedure is suited for determine the mass flow rate and pressure-drop through rupture disk seamlessly, from the point of rupture disk activation (worst-case scenario) to the point when the system fully depressurizes beyond regulatory compliance.
Metadaten
Author:Mondie Kimandi Mutegi
URN (permanent link):urn:nbn:de:hbz:386-kluedo-59897
Advisor:Jürgen Schmidt
Document Type:Doctoral Thesis
Language of publication:English
Publication Date:2020/06/13
Year of Publication:2020
Publishing Institute:Technische Universität Kaiserslautern
Granting Institute:Technische Universität Kaiserslautern
Acceptance Date of the Thesis:2020/06/03
Date of the Publication (Server):2020/06/15
Tag:150 bar loop; bursting disk; dischargeable mass flow rate; pressure drop; rupture disk
GND-Keyword:pressure relief
Number of page:XVII, 162
Faculties / Organisational entities:Fachbereich Maschinenbau und Verfahrenstechnik
DDC-Cassification:6 Technik, Medizin, angewandte Wissenschaften / 620 Ingenieurwissenschaften und Maschinenbau
MSC-Classification (mathematics):76-XX FLUID MECHANICS (For general continuum mechanics, see 74Axx, or other parts of 74-XX)
Licence (German):Creative Commons 4.0 - Namensnennung, nicht kommerziell, keine Bearbeitung (CC BY-NC-ND 4.0)